Tips and wrinkles 2

To keep the page sizes of biopowered wiki managable, we've started a second Tips and wrinkles page ...

See also tips and wrinkles 1.

Auto shut off misting nozzle

You need to find a brass ball cock valve then a female hozelock type fitting will fit onto the the inlet (3/4") or use a reducer if it is a 1/2" BSP. The moveable outlet can be unscrewed and replaced with a 10 mm 90 degree compression fitting,bend a piece of 10 mm copper pipe to achieve the desired height and angle,onto the end of this fit a reducer to take you to the required misting nozzle size,in this case 10 mm to 22 mm, Work out the desired height on your wash tank and fit,i find this useful as my tank is outside and there is a chance that the tank outlet could freeze in winter

• click to enlarge
• 

  Complete set up. Source: K.H

• click to enlarge
• 

  Tank fitting. Source: K.H

• click to enlarge
• 

  Nozzle Source: K.H

KH 21:41, 19 October 2012 (BST)KHKH 21:41, 19 October 2012 (BST)

Centrifuge vial holder

An easy to make holder for the vials used in a two stage non titration,it also makes the drop out very visible You need 8" of gutter and a circular downpipe bracket, attach by cutting two holes in the gutter near the top,pass the two ends of the bracket through the holes and glue in place

• click to enlarge
• 

  Holder. Source: K.H

• click to enlarge
• 

  Holder. Source: K.H

KH 21:41, 19 October 2012 (BST)KHKH 21:41, 19 October 2012 (BST)

Y Piece

Useful for separating off the flow when using an Eductor Just a case of filing/grinding away on the two bits of pipe untill you get a nice close fit and then silver soldering in place

• click to enlarge
• 

  Y piece. Source: K.H

KH 22:47, 25 June 2011 (BST)

Using "Hozelock" type quick release connectors

Not to be used in the bio making process

The brass type hozelock connectors can be useful for various connections outside of making bio and can be used on small bore( ID 14mm) piping BUT you need to replace the O ring with a "Viton" type The O ring is 2mm with a diameter of 12mm,the plastic that clamps the pipe to the fitting is ok with biodiesel but they can be done away with and a jubilee clip used anyway,they also remain airtight upto about 20 PSI (see pics)

• click to enlarge
• 

  Male and female. Source: K.H

• 

  Pressure testing. Source: K.H

• 

  20 PSI. Source: K.H

• 

  Male fitting. Source: K.H

KH 23:45, 25 June 2011 (BST)

Micro HPT

Quick, simple and cheap method for performing the HPT which means you don't have to use the kitchen stove with associated smell in the house!

1 night light, the container from a second and a piece of bent electrical wire. It reaches temperature very quickly, but due to the flimsy nature of the container, cools down when the oil is added. So it needs to be left with the flame burning for a few minutes to reheat.

• Micro HPT
• 

Bio-rich-time-poor 12:10, 26 June 2011 (BST)

Drum lid removal

A novel idea from littledave. Slice through a drum seam with a 1mm cutting disk on an angle grinder and you have a removable lid. Dave recommends marking the lid and drum so the lid can be replaced in the same position each time. Not all drums will be perfectly circular and the position of the cut may not be in the same place around the circumference.

• Drum seam cutting
• 
• 

Bio-rich-time-poor 23:15, 27 June 2011 (BST)

Quick and easy large capacity funnel

You can make a large capacity funnel by cutting the bottom off of an old water dispenser bottle. They are such a good interferance fit in a standard 20ltr cubie that they are self supporting.

If you want a lid for your new funnel, first cut the lid from the bottom of the bottle cutting at the fattest part of a ribbed section and then cut the funnel from the remains cutting on the thinnest part of a ribbed section.

If you cut the bottle roughly in half, you get a more stable, but lower capacity, funnel ideal for use with 20ltr tins that have a slightly larger hole.

Remember to take care when you begin to fill an empty cubie as it is easy to make it top heavy and it can fall over.

• click to enlarge
• 

  20ltr Funnel

• 

  20ltr Funnel with lid

• 

  20ltr Funnel & 10ltr Funnel

max.print 23:45, 03 October 2011 (BST)

See also tips and wrinkles 1.