Mitsubishi Delica fuel system

This page is Work In Progress and therefore may not be complete.

This is a scratchpad at the moment to accumulate information!

This page describes the Mitsubishi Delica 2.8TD fuel system and problems that may occur when running on biodiesel. Note that many of these issues are problems with pump diesel too, but on a vehicle of this age biodiesel can accelerate failure in aged components.

Fuel system introduction

The Delica's 4M40 engine is equipped with a licensed copy of the Bosch VE pump, built by Zexel. This is gear driven from the crankshaft. It directly sucks fuel up from the tank through the fuel filter. All the fuel pipework is 8mm ID.

Inside the fuel tank there is a course strainer. Tank access is by removal only (no access hatches).

Tank strainer

The strainer in the tank can easily block with soaps if soapy biodiesel is run through the system. Because the in-tank strainer has a hole in the top, this blockage isn't usually noticed until the tank is down to 1/8th full, when the vehicle will stall.

The recommended solution is to drop the tank, remove the strainer, and fit an inline course filter in the engine bay, where it can be observed and easily accessed.

Fuel filter

Common replacement filters for the Delica (and Pajero) are those manufactured by Boshi.

However, Delica and Pajero filter heads are slightly different in design.

In the picture below, on the left is an OEM filter, with the Boshi filter on the right. Note that the Boshi filter has an extra seal mounted on top - this won't seal properly on the Delica, and should be removed (twist off with pliers), otherwise air ingress is likely.

Fuel pump

Zexel part number 104741-3323 (Mitsubishi part number ME201700)

Cold advance solenoid

Pump internal fuel pressure (and therefore injection advance timing) is controlled by a "pulling electromagnet" (Zexel name for the green capped solenoid at the back of pump). It sits above the stop solenoid on the rear of the pump.

It is hollow up the middle and this is lined with a filter mesh. There are three outlet holes, one on the pump end of the valve (right in this photo), two on the solenoid end (left), separated by an o-ring. The o-ring is 12mm ID, seated in a 2mm slot. The barrel of the solenoid is 14mm.

The solenoid separates fuel pump overflow into two paths. This is not obvious unless you look closely at the fuel union on the back of the pump.

One path, always open, returns fuel from inside the pump to the tank (via the return pipe shared with the injector spill-off).

The other path, only open when 12V is NOT applied to the solenoid, loops the fuel from inside the pump back to the pump's inlet (lift side).

Applying 12V closes the ports on the loop side.

Its purpose in life is to advance injection timing from cold, and when up to temp return to normal. This advances the timing across the whole RPM range.

Two problems may be introduced by this valve - the internal mesh can block up with crud and affect the pump's timing (injection is too advanced). Additionally, the o-ring may no longer seal, allowing air from the return pipe to be drawn into the pump's suction side.

Cleaning

Cleaning is best done with a section of braided copper wire - the ends easily catch onto crud and pull it out.

Check that the valve actuates when 12V is applied. It should go with a fair clonk noise.

Replacement

Diesel Bob sells these for £75+VAT with £3 P&P. However, the part number he supplies is unknown.

It is believed to be manufactured by Italian company TOR, part number is 246650-5820, Zexel part 146650-5820, Bosch 9461615275. Locally it may be possible to pick one up from a diesel specialist for about £50+VAT).

This is the replacement with Zexel part number 146650-5820.

Note that it does not come supplies with an o-ring, which must be sourced separately.

However, there are notable differences. The original says "76" on the side and has two drilled ports on the loop side (three total). The new part above has "58" on the side and four drilled ports on the loop side (five total). This may lower the internal pump pressure and retard the injection timing.

Cold start spring

The pump also has cold start mechanism on side of pump. This gives extra cold idle, and advances the injection timing at lower RPM.

A spring works against a wax stat in the coolant system. When cold the mechanism turns clockwise (advanced injection & higher idle). When warm the mechanism turns anticlockwise (normal pump hydraulic timing & normal idle).

It is unusual for anything to go wrong with this mechanism.