Difference between revisions of "Multi-tasking processor"
Line 19: | Line 19: | ||
===Main parts used=== | ===Main parts used=== | ||
− | 3mts 22mm pipe | + | *3mts 22mm pipe |
− | 2x 3/4 hosetails | + | *2x 3/4 hosetails |
− | 3mt clear 1" pipe | + | *3mt clear 1" pipe |
− | 3x tees | + | *3x tees |
− | 9x 90s | + | *9x 90s |
− | 1x 45 | + | *1x 45 |
− | bypass valve | + | *bypass valve |
− | 5x tank connectors | + | *5x tank connectors |
− | 5x nylon washers | + | *5x nylon washers |
− | 3x joiners | + | *3x joiners |
− | 4x 3/4"-22mm | + | *4x 3/4"-22mm |
− | 6x full bore valves | + | *6x full bore valves |
− | 2x pressure gauges | + | *2x pressure gauges |
− | 18" immersion heater | + | *18" immersion heater |
− | 3x 10" filters plus brackets/elements | + | *3x 10" filters plus brackets/elements |
− | mechanical flange | + | *mechanical flange |
− | 400mic drum filter | + | *400mic drum filter |
− | 205lt clip top drum | + | *205lt clip top drum |
− | 120lt HDPE clip top drum | + | *120lt HDPE clip top drum |
− | tam 105 pump | + | *tam 105 pump |
− | 2x 1"-22mm | + | *2x 1"-22mm |
− | 4 mt flex | + | *4 mt flex |
− | 2 plugs | + | *2 plugs |
− | 22-15-22 tee | + | *22-15-22 tee |
− | 1x 15mm ball valve | + | *1x 15mm ball valve |
Total cost @ 01/05/11 £325 | Total cost @ 01/05/11 £325 |
Revision as of 19:27, 18 May 2011
This page is Work In Progress and therefore may not be complete. |
Use the code above if you are working on the page. Delete it when the page is finished and complete. Delete this text once you have read it.
This is a parts list and description of my KH dewatering and filter set up which includes a bypass to keep the filters within there pressure rating
Main parts used
- 3mts 22mm pipe
- 2x 3/4 hosetails
- 3mt clear 1" pipe
- 3x tees
- 9x 90s
- 1x 45
- bypass valve
- 5x tank connectors
- 5x nylon washers
- 3x joiners
- 4x 3/4"-22mm
- 6x full bore valves
- 2x pressure gauges
- 18" immersion heater
- 3x 10" filters plus brackets/elements
- mechanical flange
- 400mic drum filter
- 205lt clip top drum
- 120lt HDPE clip top drum
- tam 105 pump
- 2x 1"-22mm
- 4 mt flex
- 2 plugs
- 22-15-22 tee
- 1x 15mm ball valve
Total cost @ 01/05/11 £325
What it does
The wvo goes into the drum via a 400 micron drum filter,its then heated with the option of circulating to speed dewatering,it is then pumped into the storage drum via 20 and 5 micron filters,most filters are rated at 0.8 bar so there is a bypass valve which ensures the oil is never forced through the filters,from the storage drum the oil goes through a 1 micron filter to the car/drums
Safety features
There is a float switch which cuts out the pump at low oil levels and if either filter blocks the bypass valve will send the oil back into the main drum where it will just circulate in a loop
What i was trying to achieve
My aim was to make a self contained filter unit to which you can add extra storage drums as needed but to also be affordable