Difference between revisions of "Cone bottoms for tanks"

From Biopowered
Jump to: navigation, search
 
(15 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
{{WIP}}
+
[[File:Cone_Calculator_grab.png|500px|right|link=http://www.biopowered.co.uk/forum/tools/cone.php |thumb|Cone calculator. Source: Tony. Click graphic to access.]]
 +
Cone bottomed tanks facilitate accurate splitting of oil and water, oil and glycerol (if you [[glycerol wash]]) or glycerol and biodiesel.
  
 +
The easiest way to generate the shape or development for a conical bottom is to use the calculator complied by Tony.  For security reasons this has to be located outside of the wiki, but it can be accessed via this link or by clicking on the grahpic, right …
  
−
==This is currently a draft page for JamesRL's scrutiny.==
 
  
−
[[File:Conebottom1.png]]
+
[http://www.biopowered.co.uk/forum/tools/cone.php Biopowered cone calculator.]
  
  
−
Forget the hole in the top for the time being so, to find length of sloping side ‘L’
+
Use of the calculator should be self explanatory, but you will need to enter the following information.  Tank or drum diameter.  Required cone height or required cone angle and the outside diameter of the fitting you intend to use.  For these three parameters the calculator will provide all the dimensions to manufacture a cone.
 +
<BR>
 +
<BR>
  
−
Base dia ‘D’ = 570mm (typical for a 205 litre steel drum, but check before proceeding)  hence base radius ‘R’ is half this = 285
 
−
Desired angle ‘a’, say = 45°
 
  
−
For any size cone where angla '''a''' is 45° L = Square root of 2 (1.414) x R
+
[[File:Conical_bottom_JamesRL.jpg‎|400px|thumb|left|Fabricated cone bottom.  Source: JamesRL.]]
 +
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
 +
<BR>
  
  
−
To address the hole in the top, use the same formula but substitute the diameter of the fitting you want to use for the base diameter, say 30mm
 
−
Hence if  D = 30, R will = 15
 
  
−
l = Square root 2 (1.414) x 15 = 21.21
+
Before making a start with a metal cone it may be advantageous to check everything fits correctly by making a paper or card test cone, it could save you a great deal of time in the long run!
  
−
We are aiming for this shape to roll into the cone,
+
[[File:Cone_bottom_tab.png‎]]
  
 +
If required a tab can be added to the development to assist in assembly and welding.
  
−
[[File:Conebottom2.png]]
 
  
  
−
so we need to know the angle between the two edges (b°).
 
−
We’ve already calculated L, 403mm.
 
−
 
−
The Included angle is simple to work out it's 180 x D / L
 
−
 
−
Giving us 180 x 570 / 403 = 254.59°
 
−
 
−
To fabricate a 60° cone draw a semi-circle with a radius equal to the finish diameter, for a steel drum that's 570mm.
 
−
The hole at the apex is the same, use a radius the same as the finished diameter.
 
  
  
 
<gallery caption="Steps in producing a cone bottom" widths="400px" heights="500px" perrow="2" align="left">
 
<gallery caption="Steps in producing a cone bottom" widths="400px" heights="500px" perrow="2" align="left">
 
File:Conebottomphoto1 source rob-b.jpg|Blank for cone. Source: Rob-b
 
File:Conebottomphoto1 source rob-b.jpg|Blank for cone. Source: Rob-b
−
File:Conebottomphoto2 source rob-b.jpg|Arc for cone cut from blank. Source: Rob-b
+
File:Conebottomphoto2 source rob-b.jpg|Development for cone cut from blank. Source: Rob-b
−
File:Conebottomphoto3 source rob-b.jpg|Arc formed to cone and tack welded Source: Rob-b
+
File:Conebottomphoto3 source rob-b.jpg|Development formed to cone and tack welded Source: Rob-b
 
File:Conebottomphoto4 source rob-b.jpg|Finished cone with fitting welded to tank. Source: Rob-b
 
File:Conebottomphoto4 source rob-b.jpg|Finished cone with fitting welded to tank. Source: Rob-b
 
</gallery>
 
</gallery>
 +
 +
 +
[[Category:Biodiesel]]
 +
[[Category:Processors and equipment]]

Latest revision as of 18:58, 10 June 2013

Cone calculator. Source: Tony. Click graphic to access.

Cone bottomed tanks facilitate accurate splitting of oil and water, oil and glycerol (if you glycerol wash) or glycerol and biodiesel.

The easiest way to generate the shape or development for a conical bottom is to use the calculator complied by Tony. For security reasons this has to be located outside of the wiki, but it can be accessed via this link or by clicking on the grahpic, right …


Biopowered cone calculator.


Use of the calculator should be self explanatory, but you will need to enter the following information. Tank or drum diameter. Required cone height or required cone angle and the outside diameter of the fitting you intend to use. For these three parameters the calculator will provide all the dimensions to manufacture a cone.


Fabricated cone bottom. Source: JamesRL.




















Before making a start with a metal cone it may be advantageous to check everything fits correctly by making a paper or card test cone, it could save you a great deal of time in the long run!

Cone bottom tab.png

If required a tab can be added to the development to assist in assembly and welding.



  • Steps in producing a cone bottom

  • Blank for cone. Source: Rob-b

  • Development for cone cut from blank. Source: Rob-b

  • Development formed to cone and tack welded Source: Rob-b

  • Finished cone with fitting welded to tank. Source: Rob-b

Retrieved from ‘https://biopowered.co.uk/w/index.php?title=Cone_bottoms_for_tanks&oldid=4059’