Difference between revisions of "Melting stick"
(→First heading here) |
|||
| Line 1: | Line 1: | ||
| − | |||
| − | |||
<metadesc>Solid oil melting stick</metadesc> | <metadesc>Solid oil melting stick</metadesc> | ||
| Line 6: | Line 4: | ||
{{WIP}} | {{WIP}} | ||
| − | + | The melting stick is made from a 220-240 volt cartridge heater,it will melt solid oil and is small enough to go through screw top lids | |
| + | __TOC__ | ||
| − | |||
| + | ==The melting stick== | ||
| − | + | [[File:Melting_stick_003.jpg |250px|thumb|centre|The cartridge heater]] | |
| − | |||
| − | |||
| − | + | [[File:Melting_stick_008.jpg |250px|thumb|centre|The business end]] | |
| − | |||
| − | |||
| − | [[File:Melting_stick_008.jpg |250px|thumb| | ||
==List of parts== | ==List of parts== | ||
| − | + | Cartridge heater 15 mm 300W (available in various wattages) | |
| − | |||
| − | |||
| − | + | 2 x 15 mm straight joiner-compression | |
| − | + | Short length of 15 mm copper pipe bent to 90 degrees | |
| + | Speedfit type insert | ||
| − | + | 2 ft of plastic 15 mm pipe | |
| − | |||
| − | + | Cable and plug | |
| − | |||
| − | + | 2 connectors and insulating tape | |
| − | + | Flat piece of metal slightly longer than the heater | |
| − | |||
| − | |||
| + | [[File:Melting_stick_002.jpg|250px|thumb|centre|List of parts used,click to enlarge]] | ||
| + | |||
| − | + | ||
| − | |||
| − | |||
| − | === | + | ===How to assemble=== |
| − | + | Firstly solder the flat piece of steel to one of the flat surfaces of a compression nut,this needs to end up at the bottom and is a stand off to keep the heater away from the container walls,tighten the heater into a straight connector using the nut with the stand off then attach the 90 copper pipe,this needs to be short enough that the heater wires protrude. | |
| + | Attach the other connector to the other end of the copper pipe. | ||
| + | Put an insert into one end of the plastic pipe and feed the cable down the pipe,connect and insulate the heater to the cable then join the plastic pipe to the connector. | ||
| − | + | [[File:Melting_stick_005.jpg |250px|thumb|centre|Melting its way into a tub]] | |
| + | |||
| − | |||
| − | |||
| − | |||
==See also== | ==See also== | ||
Use if there are similar pages in the wiki, if not delete. | Use if there are similar pages in the wiki, if not delete. | ||
| Line 72: | Line 61: | ||
* Link within this wiki here | * Link within this wiki here | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | ~~KH~~ | |
| − | |||
<nowiki> ... delete this "nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!) | <nowiki> ... delete this "nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!) | ||
| − | |||
| − | |||
For Biodiesel ... | For Biodiesel ... | ||
| − | [[Category:Biodiesel]] | + | [[Category:Biodiesel]] |
| − | |||
| − | |||
[[Category:Ingredients and preparation]] | [[Category:Ingredients and preparation]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | [[Category: | + | [[Category:vegetable oil]] |
| − | |||
[[Category:Filtration & drying equipment]] | [[Category:Filtration & drying equipment]] | ||
| − | |||
| − | |||
| − | |||
Please Note: To get your page indexed on the main page it is necessary, to got to the main page, click the edit tab and then click save. | Please Note: To get your page indexed on the main page it is necessary, to got to the main page, click the edit tab and then click save. | ||
</nowiki> ... delete this "/nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!) | </nowiki> ... delete this "/nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!) | ||
Revision as of 22:41, 19 October 2012
 This page is Work In Progress and therefore may not be complete.
|
The melting stick is made from a 220-240 volt cartridge heater,it will melt solid oil and is small enough to go through screw top lids
The melting stick
List of parts
Cartridge heater 15 mm 300W (available in various wattages)
2 x 15 mm straight joiner-compression
Short length of 15 mm copper pipe bent to 90 degrees
Speedfit type insert
2 ft of plastic 15 mm pipe
Cable and plug
2 connectors and insulating tape
Flat piece of metal slightly longer than the heater
How to assemble
Firstly solder the flat piece of steel to one of the flat surfaces of a compression nut,this needs to end up at the bottom and is a stand off to keep the heater away from the container walls,tighten the heater into a straight connector using the nut with the stand off then attach the 90 copper pipe,this needs to be short enough that the heater wires protrude. Attach the other connector to the other end of the copper pipe. Put an insert into one end of the plastic pipe and feed the cable down the pipe,connect and insulate the heater to the cable then join the plastic pipe to the connector.
See also
Use if there are similar pages in the wiki, if not delete.
- Link within this wiki here
- Link within this wiki here
- Link within this wiki here
~~KH~~
... delete this "nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!)
For Biodiesel ...
[[Category:Biodiesel]]
[[Category:Ingredients and preparation]]
[[Category:vegetable oil]]
[[Category:Filtration & drying equipment]]
Please Note: To get your page indexed on the main page it is necessary, to got to the main page, click the edit tab and then click save.
... delete this "/nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!)
