Difference between revisions of "Pump - Tam 105"
| Line 74: | Line 74: | ||
| + | <gallery caption="Tam 105 impeller replacement replacement" widths="280px" heights="200px" perrow="3" align="center"> | ||
| + | File:Tam 01 Rob-b.jpg|The body is removed by undoing three screws. | ||
| + | File:Tam 02 Rob-b.jpg|Removing the body reveals the impeller. The impeller is a friction fit on the shaft and is fitted with a round ended parallel key. | ||
| + | File:Tam 03 Rob-b.jpg|The impeller material appears to be quite soft, so levering it off the shaft is not recommended. This simple puller was made to engage with the groove on the impeller boss. | ||
| + | File:Tam 04 Rob-b.jpg|Another view of the puller. | ||
| + | File:Tam 05 Rob-b.jpg|The puller engages with this groove. The impeller is not a very tight fit on the shaft. | ||
| + | File:Leo XKM60 puller in position.JPG|The fingers of the puller are clamped into the groove by tightening a hose clip around it. | ||
| + | |||
| + | </gallery> | ||
Revision as of 21:32, 10 February 2012
The TAM 105 1" centrifugal pump is the most popular pump for use in biodiesel processers but remember you are buying a pump that is marketed for clean water only,the figures below only apply to water but are good for comparisons.
TAM 105 specifications
- Motor 230V 50Hz 1ph
- Power 330Watts
- Current 1.4Amps
- Capacitor 8uF 450V
- Speed 2800rpm
- Max. Head 35M
- Max. Lift (Suction) 7M
- Bore Size 1”BSP
- Max. Output 40L/min
- Weight 7.2kg
- Part No. 7230350
External link to Product Manual
Components
- Pump Body Cast Iron (Painted)
- Impellor Case Cast Iron (Painted)
- Impellor Case Seal NBR
- Motor Shaft Seal NBR
- Rotor / Gear / Impellor Brass
- Shaft Key / Nut Stainless Steel
- Motor Shaft Stainless
Performance
- Voltage / Frequency 230v / 50Hz
- kW 0.33
- Amps 1.4
- RPM 2800
- Duty Cycle Continuous
- Bypass Valve Y/N N
- Max Flow 40 lpm @ 0 m head
- Discharge Pressure 3.5 Bar / 50.75 PSI
- Max Suction Lift (Dry) None
- Max Suction Lift (Wet) 7 m
- Inlet Fitting 1" BSP
- Outlet Fitting 1" BSP
- Max Particle Tolerance 100 Micron
- Max Liquid Temp 90 Celcius
- Max Room Temp 40 Celcius
- Thermal Protection Y/N Y
- Max Liquid Viscosity Water
- Ingress Protection IP44
Spares
Spares for this pump are readily available from the main stockists and distributors whose details can be found on the internet
Accessories
- Foot Valve Filter 7950561
- BSP Spigot Hose Connector 7950210
- I.D. Reinforced Hose for Suction and delivery 7955010
- I.D. Layflat Hose for delivery only 7955110
- Fuse Rating - 5 Amps
- Tam 105 impeller replacement replacement
The body is removed by undoing three screws.
Removing the body reveals the impeller. The impeller is a friction fit on the shaft and is fitted with a round ended parallel key.
The impeller material appears to be quite soft, so levering it off the shaft is not recommended. This simple puller was made to engage with the groove on the impeller boss.
Another view of the puller.
The puller engages with this groove. The impeller is not a very tight fit on the shaft.
The fingers of the puller are clamped into the groove by tightening a hose clip around it.
KH 19:35, 11 December 2010 (UTC)
