Difference between revisions of "Pump - Tam 105"
(→Components) |
(→Performance) |
||
| Line 35: | Line 35: | ||
==Performance== | ==Performance== | ||
| − | Voltage / Frequency 230v / 50Hz | + | * Voltage / Frequency 230v / 50Hz |
| + | * kW 0.33 | ||
| + | * Amps 1.4 | ||
| + | * RPM 2800 | ||
| + | * Duty Cycle Continuous | ||
| + | * Bypass Valve Y/N N | ||
| + | * Max Flow 40 lpm @ 0 m head | ||
| + | * Discharge Pressure 3.5 Bar / 50.75 PSI | ||
| + | * Max Suction Lift (Dry) None | ||
| + | * Max Suction Lift (Wet) 7 m | ||
| + | * Inlet Fitting 1" BSP | ||
| + | * Outlet Fitting 1" BSP | ||
| + | * Max Particle Tolerance 100 Micron | ||
| + | * Max Liquid Temp 90 Celcius | ||
| + | * Max Room Temp 40 Celcius | ||
| + | * Thermal Protection Y/N Y | ||
| + | * Max Liquid Viscosity Water | ||
| + | * Ingress Protection IP44 | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Spares== | ==Spares== | ||
Revision as of 21:43, 11 December 2010
The TAM 105 1" centrifugal pump is the most popular pump for use in biodiesel processers but remember you are buying a pump that is marketed for clean water only,the figures below only apply to water but are good for comparisons.
TAM 105 specifications
- Motor 230V 50Hz 1ph
- Power 330Watts
- Current 1.4Amps
- Capacitor 8uF 450V
- Speed 2800rpm
- Max. Head 35M
- Max. Lift (Suction) 7M
- Bore Size 1”BSP
- Max. Output 40L/min
- Weight 7.2kg
- Part No. 7230350
Components
- Pump Body Cast Iron (Painted)
- Impellor Case Cast Iron (Painted)
- Impellor Case Seal NBR
- Motor Shaft Seal NBR
- Rotor / Gear / Impellor Brass
- Shaft Key / Nut Stainless Steel
- Motor Shaft Stainless
Performance
- Voltage / Frequency 230v / 50Hz
- kW 0.33
- Amps 1.4
- RPM 2800
- Duty Cycle Continuous
- Bypass Valve Y/N N
- Max Flow 40 lpm @ 0 m head
- Discharge Pressure 3.5 Bar / 50.75 PSI
- Max Suction Lift (Dry) None
- Max Suction Lift (Wet) 7 m
- Inlet Fitting 1" BSP
- Outlet Fitting 1" BSP
- Max Particle Tolerance 100 Micron
- Max Liquid Temp 90 Celcius
- Max Room Temp 40 Celcius
- Thermal Protection Y/N Y
- Max Liquid Viscosity Water
- Ingress Protection IP44
Spares
Spares for this pump are readily available from the main stockists and distributors whose detail can be found on the internet
Accessories
Foot Valve Filter 7950561
BSP Spigot Hose Connector 7950210
I.D. Reinforced Hose for Suction and delivery 7955010
I.D. Layflat Hose for delivery only 7955110
Fuse Rating
The fuse in the plug must be rated as follows:
TAM 105 ......... 5 Amps
KH 19:35, 11 December 2010 (UTC)
