Difference between revisions of "Processor build step by step"

From Biopowered
Jump to: navigation, search
Line 15: Line 15:
  
  
==First heading here==
+
==Processor tank==
 
Text and photo content here ...
 
Text and photo content here ...
 +
 +
 +
<gallery caption="This is a gallery, blah, blah, blah" widths="200px" heights="300px" perrow="4" align="left">
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
File:Ground edge of drum.jpg|Text under pic here.
 +
</gallery>
 +
 +
 +
 +
 +
Welding a cone to a drum.
 +
 +
It is far easier to weld a lap joint than try to lay a fillet considering the gauge of the drum.
 +
 +
You will need 0.6mm wire and a proper shield gas that is suitable for shallow penatration, Co2 isn't really good enough.
 +
 +
Fit the cone on the drum and tack the lap joint every 6 inch, close down any gaps between the cone and drum wall, grind flush all tacks.
 +
 +
Lay the drum on its side and weld in a downward direction between the 10 and 20 past position. You'll have to get the weld speed, amps and wire feed just right so a bit of practice will be needed before you weld in anger.
 +
 +
Grind back flush the last 15-20mm of each section of weld and start the next section on top of it, when you get to the last run of weld grind both ends flush so you start and finish over the existing welds.
 +
 +
 +
 +
 +
[[File:Ground edge of drum.jpg|600px|thumb|right|Paint ground off the cut edge]]
 +
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
 +
<br>
  
  

Revision as of 15:07, 27 March 2014


WarningIconSmall.png This page is Work In Progress and therefore may not be complete.


Brief intro, which can include a thumbnail photo, here ...


The TOC tag creates a content box. The text it contains is generated automatically based on the page headings. Delete this text once you have read it.


Processor tank

Text and photo content here ...




Welding a cone to a drum.

It is far easier to weld a lap joint than try to lay a fillet considering the gauge of the drum.

You will need 0.6mm wire and a proper shield gas that is suitable for shallow penatration, Co2 isn't really good enough.

Fit the cone on the drum and tack the lap joint every 6 inch, close down any gaps between the cone and drum wall, grind flush all tacks.

Lay the drum on its side and weld in a downward direction between the 10 and 20 past position. You'll have to get the weld speed, amps and wire feed just right so a bit of practice will be needed before you weld in anger.

Grind back flush the last 15-20mm of each section of weld and start the next section on top of it, when you get to the last run of weld grind both ends flush so you start and finish over the existing welds.



Paint ground off the cut edge























































First Sub-heading here

Text and photo content here ...

Delete if not required.


Second sub-heading here

Text and photo content here ...

Delete if not required.



Second heading here

Text and photo content here ...

Delete if not required.


First Sub-heading in second heading here

Text and photo content here ... Delete if not required.


Second Sub-heading in second heading here

Text and photo content here ...

Delete if not required.


etc etc



End the page with the headings below...

See also

Use if there are similar pages in the wiki, if not delete.

  • Link within this wiki here
  • Link within this wiki here
  • Link within this wiki here


References

Use if you need to cite reference material you've used , if not delete.

  1. First ref here
  2. Second ref here


Further reading

Use if you can detail any useful reading matter, if not delete.

  • Book details here
  • Book details here
  • Book details here

External links

Use if you can list any useful links on the internet, if not delete.

  • Link outside this wiki here
  • Link outside this wiki here
  • Link outside this wiki here


Originator to sign and date here by using 4 "squiggle marks"


... delete this "nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!) Add categories ... By using categories your page will get indexed on the wiki main page. For Biodiesel ... [[Category:Biodiesel]] sets the main category. Now select one from the following, deleting the others: [[Category:Introduction to Biodiesel]] [[Category:Ingredients and preparation]] [[Category:Processing methods]] [[Category:Processors and equipment]] [[Category:Finishing]] [[Category:Safety and Testing]] Do the same for Veg oil ... [[Category:vegetable oil]] Select one from the following, and delete the others: [[Category:Introduction to veg oil use]] [[Category:Collection & regulations]] [[Category:Filtration & drying equipment]] [[Category:Testing]] [[Category:Vehicle modifications]] If your page is applicable to both veg and bio, you can have a total of four category listings. Please Note: To get your page indexed on the main page it is necessary, to got to the main page, click the edit tab and then click save. ... delete this "/nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!)