Difference between revisions of "Melting stick"
(→The melting stick) |
|||
| Line 1: | Line 1: | ||
<metadesc>Solid oil melting stick</metadesc> | <metadesc>Solid oil melting stick</metadesc> | ||
| + | [[File:Melting_stick_2.jpg|450px|thumb|right|The business end]] | ||
| − | + | The melting stick is constructed using a 220-240 volt cartridge heater. These are readily available from on-line auction sites and other outlets. The heaters are available in 110v and 230v versions and are offered in a range of Wattages from 150W to 600W. | |
| − | The melting stick is | ||
| + | The unit described here is based on a 300W unit, a size which has proved satisfactory for melting volumes of 20 litres and greater. The design of the "tosser tube" is sufficiently compact to fit through screw top lids of plastic cubies and 20 litre tins. | ||
| + | <br> | ||
| + | <br> | ||
| + | <br> | ||
| + | <br> | ||
| + | <br> | ||
__TOC__ | __TOC__ | ||
| Line 12: | Line 18: | ||
==The melting stick== | ==The melting stick== | ||
| + | [[File:Melting_stick_001.jpg|250px|thumb|right|the finished article]] | ||
[[File:Melting_stick_0013.jpg |250px|thumb|left|The cartridge heater]] | [[File:Melting_stick_0013.jpg |250px|thumb|left|The cartridge heater]] | ||
| Line 17: | Line 24: | ||
{{#ev:youtube|5dSujLHjIKs|240|centre|Stick in action}} | {{#ev:youtube|5dSujLHjIKs|240|centre|Stick in action}} | ||
| − | + | ||
| − | |||
==List of parts== | ==List of parts== | ||
Cartridge heater 15 mm 300W (available in various wattages) | Cartridge heater 15 mm 300W (available in various wattages) | ||
| Line 50: | Line 56: | ||
[[File:Melting_stick_006.jpg|250px|thumb|left|Melting its way into a tub]] | [[File:Melting_stick_006.jpg|250px|thumb|left|Melting its way into a tub]] | ||
| − | |||
==See also== | ==See also== | ||
Revision as of 20:59, 21 October 2012
The melting stick is constructed using a 220-240 volt cartridge heater. These are readily available from on-line auction sites and other outlets. The heaters are available in 110v and 230v versions and are offered in a range of Wattages from 150W to 600W.
The unit described here is based on a 300W unit, a size which has proved satisfactory for melting volumes of 20 litres and greater. The design of the "tosser tube" is sufficiently compact to fit through screw top lids of plastic cubies and 20 litre tins.
The melting stick
List of parts
Cartridge heater 15 mm 300W (available in various wattages)
2 x 15 mm straight joiner-compression
Short length of 15 mm copper pipe
Speedfit type insert
2 ft of plastic 15 mm pipe
Cable and plug
2 connectors and insulating tape
A piece of metal slightly longer than the heater with the end bent over
How to assemble
Firstly solder the piece of steel to one of the flat surfaces of a compression nut,this needs to end up at the bottom and is a stand off to keep the heater away from the container walls,tighten the heater into a straight connector using the nut with the stand off then attach the copper pipe,this needs to be short enough that the heater wires protrude. Attach the other connector to the other end of the copper pipe. Put an insert into one end of the plastic pipe and feed the cable down the pipe,connect and insulate the heater to the cable then join the plastic pipe to the connector.
See also
Use if there are similar pages in the wiki, if not delete.
- Link within this wiki here
- Link within this wiki here
- Link within this wiki here
~~KH~~
... delete this "nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!)
For Biodiesel ...
[[Category:Biodiesel]]
[[Category:Ingredients and preparation]]
[[Category:vegetable oil]]
[[Category:Filtration & drying equipment]]
Please Note: To get your page indexed on the main page it is necessary, to got to the main page, click the edit tab and then click save.
... delete this "/nowiki" tag once you have set your categories (it's just there to stop this section getting indexed on the main page!)
